Keyence DL-RS1A/GT-70A Instrukcja Użytkownika Pobierz pdf (Strona 14)

Parameters of Commands and Responses

● Read/write data

The following table lists the types of data that can be read from and written to GT-70A Series sensor

amplifiers.

Data

number

Data name Data format

Number

of bytes

Attribute

Data range

Initial

value

050 Perform preset request * 1

R 0 - 2: Last written value

0 o 1: Perform preset

0 o 2: Perform preset reset

051 Bank switching state * 1

R 0 - 3: Current active bank

0: Switch to bank 0

1: Switch to bank 1

2: Switch to bank 2

3: Switch to bank 3

052 Timing status * 1

0: Timing input OFF or measuring

with self-timing

1: Timing input ON or not

measuring with self-timing

0: Switch while measuring

1: Switch while not measuring

053 Reset request * 1

R 0 - 1: Last written value

W0 o 1: Perform reset

060 Initial reset request * 1

R 0 - 1: Last written value

W0 o 1: Perform initial reset

061

Core alarm error/self-timing delay

error clear request

R 0 - 1: Last written value

W0 o 1: Perform error clear

070 Bank 0 HIGH setting

±***.*** 8 R/W -099.999 to +999.999

+005.000

071 Bank 0 LOW setting +002.000

072 Bank 0 preset value +000.000

073 Bank 1 HIGH setting

±***.*** 8 R/W -099.999 to +999.999

+005.000

074 Bank 1 LOW setting +002.000

075 Bank 1 preset value +000.000

076 Bank 2 HIGH setting

±***.*** 8 R/W -099.999 to +999.999

+005.000

077 Bank 2 LOW setting +002.000

078 Bank 2 preset value +000.000

079 Bank 3 HIGH setting

±***.*** 8 R/W -099.999 to +999.999

+005.000

080 Bank 3 LOW setting +002.000

081 Bank 3 preset value +000.000

090

Keylock

*1R/W

0: Unlock

1: Lock

091 Bar display mode * 1 R/W

0: Bar display mode

1: OK/NG display mode

100

*6*7

Calculation mode * 1 R/W

0: OFF

1: Maximum value

2: Minimum value

3: Degree of flatness

4: Average

5: Reference difference

6: Twist

7: Warpage

8: Thickness

101 Detection mode * 1 R/W

0: Standard

1: NG hold

2: Peak hold

3: Bottom hold

4: Peak-to-peak

102

Response time * 1 R/W

0: hsp (1.5)

1: 5 ms

2: 10 ms

3: 100 ms

4: 500 ms

5: 1000 ms

6: 5000 ms

103 Timing type * 1 R/W

0: External timing input

1: Rising edge self-timing

2: Falling edge self-timing

104 Self-timing level ±***.*** 8 R/W -099.999 to +999.999 +000.500

Parameters of Commands and Responses

*1 In the Data format column, "±" indicates that the value can be either "+" or "-". "*" signifies a

number from "0 to 9".

*2 Indicates that the data can only be read from (R), can only be written to (W), or can be both read

from and written to (R/W) the sensor amplifiers.

*3 The command is executed only when the setting of the sensor amplifiers is changed from 0 to 1 or

from 0 to 2. To re-execute the command, you must first change the setting to 0, then change it to 1 or

*4 The sensor amplifier cannot be written to in a key lock state.

*5 The sensor amplifier can only be written to if both the following conditions are met:

· "External timing input" is selected for "Timing type".

· "Bank B" is selected for "Input (pink/purple wire) function selection 2".

*6 When writing data numbers 100 and 102 to the sensor amplifiers using the SW command, it

takes more time to change their settings than usual. To determine the time it takes to change the

settings, add the following values to the T6 (Sensor amplifier settings change time) values

shown in "Time Frames of Communication Response Time" (page 15).

*7 The data number 100 can only be read from and written to the sensor amplifier main unit (ID

number 00).

105 Self-timing delay type * 1 R/W

0: Static hold

1: Delay timer

106 User-specified delay time **** 4 R/W 0 to 9999 1000

107

Static hold delay stable determination

*1R/W

0: Default

1: User

108

Static hold delay stable range

±***.*** 8 R/W +000.000 to +999.999 +000.010

110

Measurement increase/decrease

direction

*1R/W

0: Normal

1: Reversed

111 Multiplier ***.* 5 R/W 000.1 to 100.0 001.0

112 Output mode * 1 R/W

0: N.O.

1: N.C.

113 Display resolution * 1 R/W

0: 0.001

1: 0.01

2: 0.1

3: 1

114 Hysteresis ±***.*** 8 R/W +000.000 to +999.999 +000.003

115

Input (purple wire) function selection

*1R/W

0: Bank A

1: Reset

116

Input (pink/purple wire) function

selection 2

*1R/W

0: Timing input

1: Bank B

120 Store preset value * 1 R/W

0: YES

1: NO

121 Power save (eco) function * 1 R/W

0: OFF

1: HALF

2: ALL

122 Core alarm * 1 R/W

0: OFF

1: ON

2: USER

124 Check point setting ±***.*** 8 R/W -65.534 to +65.534 +000.500

125 Display filter function * 1 R/W

0: ON

1: OFF

Written data Value added to T6

Data number 100: Calculation mode Sensor amplifier response time + 200 ms

Data number 102:

Response time

Calculation mode

OFF

Sensor amplifier response time

Calculation mode

Sensor amplifier response time + 200 ms

Data

number

Data name Data format

Number

of bytes

Attribute

Data range

Initial

value

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 23 24

Komentarze do niniejszej Instrukcji

Brak uwag

Keyence DL-RS1A/GT-70A Instrukcja Użytkownika Strona 14

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Keyence DL-RS1A/GT-70A